TELEM-GW6 testing manual - Revision history

Alfred at 11:56, 1 September 2014

2014-09-01T11:56:38Z

← Older revision		Revision as of 11:56, 1 September 2014
Line 32:		Line 32:
	* multiple IP addresses		* multiple IP addresses
	* VLAN		* VLAN
	=== NTP ===		===Time===

			====Timezones====
			*modify local time zone
			*verify: localtime == console time
			*modify port time zone

			==== NTP ====
	* client		* client
	* server		* server

2013-01-29T12:41:51Z

IEC104

← Older revision		Revision as of 12:41, 29 January 2013
Line 52:		Line 52:
	====IEC104====		====IEC104====
	* Test for event loss, if network connection is removed.		* Test for event loss, if network connection is removed.
			* Redundant channels

	==== Direct protocol translation ====		==== Direct protocol translation ====
	Iec-101 <-> Iec-104		Iec-101 <-> Iec-104

2013-01-29T12:34:49Z

← Older revision		Revision as of 12:34, 29 January 2013
Line 52:		Line 52:
	====IEC104====		====IEC104====
	* Test for event loss, if network connection is removed.		* Test for event loss, if network connection is removed.
			==== Direct protocol translation ====
			Iec-101 <-> Iec-104
	===Log files===		===Log files===
	*CSV		*CSV

2013-01-29T12:25:41Z

RS232

2013-01-29T12:20:25Z

Updating software

2013-01-29T12:19:39Z

← Older revision		Revision as of 12:19, 29 January 2013
Line 24:		Line 24:
	* multiple IP addresses		* multiple IP addresses
	* VLAN		* VLAN
			=== NTP ===
			* client
			* server
			=== OpenVPN server ===
			...
	===Raw data forwarding===		===Raw data forwarding===
	*Serial -- Serial		*Serial -- Serial
Line 66:		Line 70:
	# Make sure u-boot's '''press any key to stop booting''' is disabled.		# Make sure u-boot's '''press any key to stop booting''' is disabled.
	#* Use the bootstrapper app.		#* Use the bootstrapper app.
	#* If this is not disabled, GW6 will not boot if you send any data to Port2		#* If this is not disabled, GW6 will not boot if you send any data to Port2 (GWS connected with RS232)

	===Testing Internal Clock===		===Testing Internal Clock===

2013-01-29T12:17:04Z

← Older revision		Revision as of 12:17, 29 January 2013
Line 8:		Line 8:
	* by DIP switch		* by DIP switch
	* over IEC101 or IEC104		* over IEC101 or IEC104
			* from GWS (over SSH)
	===RS232===		===RS232===
	*Baudrate		*Baudrate
	*#9600		*# 9600
	*# 19200		*# 19200
	*# 38400		*# 38400
			*# ...
	*Parity		*Parity
	*# none		*# none
Line 21:		Line 23:
	===Ethernet===		===Ethernet===
	* multiple IP addresses		* multiple IP addresses
			* VLAN

	===Raw data forwarding===		===Raw data forwarding===
Line 40:		Line 43:
	*CSV		*CSV
	** events.csv		** events.csv
	** measurments.csv		** measurments.csv (not implemented jet)
	~~***~~ not implemented jet
	* error.log		* error.log
	** archive		** archive

2012-04-30T14:09:06Z

← Older revision		Revision as of 14:09, 30 April 2012
Line 32:		Line 32:
	===Virtual objects===		===Virtual objects===
	* Controlling virtual objects		* Controlling virtual objects
			* RTA-A: clear announciator LED's digital output
	===Protocols===		===Protocols===
	* communication status object		* communication status object
Line 45:		Line 46:
	* console.log		* console.log
	** archive		** archive

	== Hardware tests ==		== Hardware tests ==
	===Testing Telem-GW6 Ports===		===Testing Telem-GW6 Ports===

2012-04-13T16:44:35Z

Testing Internal Clock

← Older revision		Revision as of 16:44, 13 April 2012
Line 68:		Line 68:
	===Testing Internal Clock===		===Testing Internal Clock===
	#Change the time in the PC		#Change the time in the PC
	#Go to TDC, GW6 Setup, Common, Time Settings and make sure that the Enable GPS is not ~~click~~.		#*GW6 software does not allow syncing to a date older than 1. january 2011
			#Go to TDC, GW6 Setup, Common, Time Settings and make sure that the Enable GPS is not selected.
	#Go to TDC, Settings and click on Gen. Int. + Time Sync.		#Go to TDC, Settings and click on Gen. Int. + Time Sync.
	#Power ON/OFF (Wait until it restarts)		#Power ON/OFF (Wait until it restarts)
	#Open Putty		#Open Putty
	##Load saved session "GW6-Timetest" and open (It will log on as martem user automatically, It will give you the time once you have type the password) // if there is no "GW6-Timetest" use IP 10.0.0.144 user: martem and once logged in, enter command: date		##Load saved session "GW6-Timetest" and open (It will log on as martem user automatically, It will give you the time once you have type the password) // if there is no "GW6-Timetest" use IP 10.0.0.144 user: martem and once logged in, enter command: date
	##Password: Xooviet0		##*Password: Xooviet0
	#The time should macht with the PCs time.//if not(like 1 jan 2000 0:xx:xx), start from 4 again(power on/off)		#The time should macht with the PCs time.//if not(like 1 jan 2000 0:xx:xx), start from 4 again(power on/off)

2012-04-13T14:09:51Z

RS232